Is this 3D model free to download?

Yes, Zip Tie Clip is free to download from Cults3D. Open it in the free Thinger app, or use the "Download from Cults3D" link to open the original listing by the creator.

Where do I download the STL file?

The download is hosted by Cults3D. Use the "Download from Cults3D" link on this page to open the original listing and grab the file, or save it to your print queue in the free Thinger app.

Designed by MakerXDesigns, published on Cults3D. Please credit the creator when sharing your print.

Can I print this at home?

Yes. This is a printable 3D model intended for home FDM and resin printers. Check the original listing for suggested print settings.

Zip Tie Clip 3D printable model by MakerXDesigns

Zip Tie Clip

Source: Cults3D by MakerXDesigns

The Zip Tie Clip is a free printable 3D model from Cults3D by MakerXDesigns. Zip Tie Clips — 1-Inch Stick-On Cable Mounts 🔗 A loose cable gets snagged, kicked and tangled. You can download the STL file from the original listing below and print it at home.

Open in Thinger (free) Download from Cults3D

30 saves Source: Cults3D Updated 2026-10-22 License: CC-BY-NC-ND · non-commercial Category: Tools & Workshop

Tags: zip tie mount, zip tie clip, cable tie mount, cable management, cable clip, adhesive mount, stick on, cord organizer, wire management, desk organization, under desk, cable routing, zip tie, cable tie, office

About this model

Zip Tie Clips — 1-Inch Stick-On Cable Mounts 🔗 A loose cable gets snagged, kicked and tangled. These are the classic stick-on zip tie mounts, printed instead of bought: stick one down, run a tie through it, and the cable stays where you routed it. I printed a plate of 14 and put them to work under my desk and along the cable for the light on my desk hutch. 🟩 𝗪𝗛𝗔𝗧 𝗠𝗔𝗞𝗘𝗦 𝗜𝗧 𝗪𝗢𝗥𝗞 ▸ 𝗙𝗹𝗮𝘁 𝟭-𝗜𝗻𝗰𝗵 𝗕𝗮𝘀𝗲 — The square bottom takes a square of double-sided foam mounting tape. ▸ 𝗙𝗼𝘂𝗿-𝗪𝗮𝘆 𝗧𝗶𝗲 𝗧𝘂𝗻𝗻𝗲𝗹 — A bridged hub in the middle leaves a tunnel in both directions, so the tie runs whichever way the cable goes. ▸ 𝗦𝘁𝗮𝗻𝗱𝗮𝗿𝗱 𝗧𝗶𝗲𝘀 — The tunnel is 5.5mm wide, so common 4.8mm (3/16") ties and anything narrower fit. ▸ 𝗖𝗵𝗲𝗮𝗽 𝗧𝗼 𝗠𝗮𝗸𝗲 — About 20 minutes and under 2 g each, so print a whole plate. 🟩 𝗛𝗢𝗪 𝗧𝗢 𝗜𝗡𝗦𝗧𝗔𝗟𝗟 …

Frequently asked questions

Is this 3D model free to download?: Yes. Zip Tie Clip is free to download from Cults3D. Open it in the free Thinger app, or use the "Download from Cults3D" link above to open the original listing.
Where is the STL hosted?: The download is hosted by Cults3D, not by Thinger. We link you directly to the original listing by MakerXDesigns.
Who made this model?: Designed by MakerXDesigns, published on Cults3D. Please credit the creator when sharing your print online.
Can I print this at home?: Yes. This model is intended for home FDM and resin 3D printers. Check the original listing for suggested print settings like layer height and supports.