Is this 3D model free to download?

Yes, Cell Phone mount using the cubby on a 1999 - 2004 Jeep Grand Cherokee (WJ) is free to download from Thingiverse. Open it in the free Thinger app, or use the "Download from Thingiverse" link to open the original listing by the creator.

Where do I download the STL file?

The download is hosted by Thingiverse. Use the "Download from Thingiverse" link on this page to open the original listing and grab the file, or save it to your print queue in the free Thinger app.

Designed by zBeeble, published on Thingiverse. Please credit the creator when sharing your print.

Can I print this at home?

Yes. This is a printable 3D model intended for home FDM and resin printers. Check the original listing for suggested print settings.

Cell Phone mount using the cubby on a 1999 - 2004 Jeep Grand Cherokee (WJ) 3D printable model by zBeeble

Cell Phone mount using the cubby on a 1999 - 2004 Jeep Grand Cherokee (WJ) photo 1

Cell Phone mount using the cubby on a 1999 - 2004 Jeep Grand Cherokee (WJ) photo 2

Cell Phone mount using the cubby on a 1999 - 2004 Jeep Grand Cherokee (WJ) photo 3

Cell Phone mount using the cubby on a 1999 - 2004 Jeep Grand Cherokee (WJ) photo 4

Cell Phone mount using the cubby on a 1999 - 2004 Jeep Grand Cherokee (WJ)

Source: Thingiverse by zBeeble

The Cell Phone mount using the cubby on a 1999 - 2004 Jeep Grand Cherokee (WJ) is a free printable 3D model from Thingiverse by zBeeble. Here is my cellphone or tablet holder for the 1999-2004 Jeep Grand Cherokee (which is also called the WJ jeep). You can download the STL file from the original listing below and print it at home.

Open in Thinger (free) Download from Thingiverse

30 saves Source: Thingiverse Updated 2026-11-01 License: CC-BY-NC · non-commercial Category: Vehicles & RC

Tags: cellphone, cellphone holder, jeep, Jeep WJ, openscad, smartphone holder

About this model

Here is my cellphone or tablet holder for the 1999-2004 Jeep Grand Cherokee (which is also called the WJ jeep). It uses a cubby in the dash (see pic) that I think might contain an ashtray in some models. In mine, it just had a little rubber mat. Remove the mat, insert the print --- and vollia! A Sturdy cell phone holder. There are 3 OpenSCAD files. The "SolidMount" file will make the bottom bit that fills the hole. You'll need setting 2 and 3. These are set to print without support, but you'll have to flip over the top in your slicer. The result is a good friction fit into the cubby. The Rod file makes the rod (obviously). You can set the length. If your print bed is 200x200 (like mine) then your max print is 250mm (which is roughly 270mm once you include the ends). Y'know ... C^2=A^2+B^2.…

Frequently asked questions

Is this 3D model free to download?: Yes. Cell Phone mount using the cubby on a 1999 - 2004 Jeep Grand Cherokee (WJ) is free to download from Thingiverse. Open it in the free Thinger app, or use the "Download from Thingiverse" link above to open the original listing.
Where is the STL hosted?: The download is hosted by Thingiverse, not by Thinger. We link you directly to the original listing by zBeeble.
Who made this model?: Designed by zBeeble, published on Thingiverse. Please credit the creator when sharing your print online.
Can I print this at home?: Yes. This model is intended for home FDM and resin 3D printers. Check the original listing for suggested print settings like layer height and supports.